January 28, 2018 - Full Octane Garage

Daily Archives: January 28, 2018

Harbor Freight One Man Brake Bleeder Product Review

January 28, 2018 Banner, How To, Just Cool, Product Review

This is a review of a one man pneumatic brake bleeder from Harbor Freight. The results are surprising!

We found a very similar unit on Amazon and if you use the link below to support our channel you will get FREE SHIPPING!

https://amzn.to/2J7wh3P

Harbor freight Pittsburgh® Automotive – Item#92924

https://www.harborfreight.com/brake-fluid-bleeder-92924.html

Please SUBSCRIBE AND FOLLOW US

Categories
Categories

Facebook

Archives
Archives

Recent Posts
- 1950 Chevy 5 Window Truck Project Update 6/18/17
  
  We have been making a little progress on the 50 Five Window. I am hoping just a few more nights and I will be able to Read More »
- Pink Floyd Day 13
  
  Day 13 started the Media Blasting with baking soda. It is quite messy but very cool! [nggallery id=33] Read More »
- ICT Billet High Mount Narrow Bay AC Bracket Review (LS1/LS2/LS3 or Vortec 5.3) Part #551352-3
  
  We had bought an ICT Billet A/C Bracket part# 551494-3 and installed iton a 5.3 Vortec LS engine but unfortunately I did not measure where my Read More »
- Insite from Jessie James
  
  Some people dislike him, some love him, say what you want but this post from Jessie James makes a lot of sense. ========================================== West Coast Choppers Read More »
- 1955 MG TF New Top Project
  
  After 2 years of having a new rag top in the box we finally got around to installing the new top. It looks so much nicer Read More »
- 1963 Corvette Split Window (Project Second Chance)
  
  Well it seems I am a gluten for punishment, I am back for my 4th build since 2012. At the end of each build I keep Read More »
- Very cool Camper
  
  This is a very cool camper. Read More »
- The Redneck Spin Chair
  
  This would be a crazy ride, not sure I could handle it! Read More »
- Looking More Like A Car!
  
  We finally got all of the body parts back on the car so it is looking more like a real car now. Read More »
- Checking out the 2016 Mclaren 570S at Nashville CarsnCoffee!
  
  A fellow car enthusiast shared his new McLaren 570S with us at Nashville Cars n Coffee! Thanks for bring it out, Billy! Read More »
- Project 63 – Interior Progress Update 5/13/13
  
  I am finally making good progress on the interior. I was able to get the Second Skin heat mat down and I got the whole rear compartment other Read More »
- Project 63 Engine Bay Refresh
  
  I am making progress on the engine bay refresh. It is getting close to the point I can start putting things back together 🙂 Don’t mind Read More »
- Pink Floyd Day 3
  
  We made a lot of progress on day 3 of tear down. We finished up removing the bumpers, the trunk, rear deck lid and finished up Read More »
- A Day at the Porsche Driving Experience
  
  The Full Octane Garage was invited down to Porsche North American Headquarters in Atlanta by Hagerty’s for a special meet and greet and to check out Read More »
- Removing and Storing the Freedom Roof Panels for the Jeep Wrangler Unlimited
  
  Today the Full Octane Garage will cover, with the help of our good friend Elvis from the Golden Drive and our fellow Jeep enthusiast, Zlatko, how Read More »
- Only in Tennessee
  
  Only in Tennessee, it sure does not look like he is walking on the track 🙂 Read More »
- Initial Engine Start Up
  
  Here are a couple of clips of the initial engine start up. 1st Attempt to Start Disaster, starter stuck engaged 🙂 2nd Attempt at Engine Start Read More »
- 1956 Bel Air 4 door Resto-Mod LS1 EFI 5.3/4L60E
  
  ————————————————– This is a very recent restoration, the body was stripped to bare metal and the car had very little rust. The front floor pans and Read More »
- Pink Floyd – Week 17 progress
  
  Week 17 has been busy. We started putting the frame back together. The new front suspension is now complete, the brake lines are plumbed and we are close Read More »
- Fresh 6.0 Aluminum and a Fresh 5.3 Arrived
  
  I have been on the hunt for two LS motors for my two truck projects. A friend swapped out his freshly built 5.3 for a 6.0 Read More »
- What’s New At The Full Octane Garage (12/2/18 Update)
  
  Full Octane Garage Project Updates (1933 Auburn is in paint) Read More »
- 1950 Chevy Truck Body Install
  
  We finally mounted the body on the frame of the 1950 Chevy Truck. Read More »
- Atlanta Motor Speedway Autorama April 22 & 23
  
  The folks with the Atlanta Motor Speedway did an awesome multi-page article on Debby’s 31 Auburn in the Grease Magazine for the upcoming Motorama on Apr Read More »
- Harbor Freight One Man Brake Bleeder Product Review
  
  This is a review of a one man pneumatic brake bleeder from Harbor Freight. The results are surprising! We found a very similar unit on Amazon Read More »
- Retrofit Modern Gauges in 1950 Chevy Truck
  
  We decided to Retrofit Modern Gauges in our 1950 Chevy Truck project but it turned out to be a bit more complicated that we had anticipated. Read More »
- Project 63 got some color today!
  
  Project 63 got some color today! Pictures of Dennis doing the final shooting. Read More »
- Engine and Trans mocked up in Project 50 Five Window
  
  We finally got back to work on the truck tonight, managed to get the LS engine and 4L60E transmission mocked up on the chassis. Tomorrow’s project Read More »
- First Attempt Cutting Up the 1988 Corvette with the Eastwood Versa-Cut 60 Plasma Cutter
  
  This was our First Attempt with the Eastwood Plasma Cutter. You get to have a good laugh about mid way through when some hot sparks landed Read More »
- you know you are a Car Guy if… Episode 1
  
  1st in a series of short videos that define the Real “Car Guy”! Let us know what you think in the comments! Read More »
- Pink Floyd Gets Some Teeth
  
  Pink Floyd no longer looks like he is from TN, he now has teeth in his new Grille. We also go the back bumpers installed, now Read More »